My Vintage Stove Leaks Around the Top Door
I picked up this vintage coal stove and restored the mica. I've got it piped and when I light a small wood fire the draw is great but it leaks too much smoke out of the flip up door on the top.
I suspect this may have had a seal on it at one point. What would be a suitable gasket for this stove?
I suspect this may have had a seal on it at one point. What would be a suitable gasket for this stove?
Attachments
- SMITTY
- Member
- Posts: 12526
- Joined: Sun. Dec. 11, 2005 12:43 pm
- Location: West-Central Mass
- Stoker Coal Boiler: EFM 520 Highboy
- Coal Size/Type: Rice / Blaschak anthracite
- Other Heating: Oil fired Burnham boiler
Probably just needs some of this: http://www.allstategasket.com/info_boiler_gaskets ... pes-01.asp
That link was the first thing that I got on a search for fiberglass rope gasket -- there are probably 100 more places out there. You'll just have to figure out what thickness you need so the door stays closed properly.
That link was the first thing that I got on a search for fiberglass rope gasket -- there are probably 100 more places out there. You'll just have to figure out what thickness you need so the door stays closed properly.
- Richard S.
- Mayor
- Posts: 15243
- Joined: Fri. Oct. 01, 2004 8:35 pm
- Location: NEPA
- Stoker Coal Boiler: Van Wert VA1200
- Coal Size/Type: Buckwheat/Anthracite
That rope is fire resistant, it's not regular rope.
Most fireplace/stove places should have it for any length you want.
Most fireplace/stove places should have it for any length you want.
- coaledsweat
- Site Moderator
- Posts: 13767
- Joined: Fri. Oct. 27, 2006 2:05 pm
- Location: Guilford, Connecticut
- Stoker Coal Boiler: Axeman Anderson 260M
- Coal Size/Type: Pea
Find a local HVAC supply house or stove shop and purchase a proper gasket, bring the old piece with you to match it as there are a variety of sizes. Rope describes what it looks like, it is actualy a glass product woven into a rope like appearance.Dr Cherry wrote:Maybe I can experiment with some rope. Thanks for confirming my first instinct.
- Poconoeagle
- Member
- Posts: 6397
- Joined: Sat. Nov. 08, 2008 7:26 pm
- Location: Tobyhanna PA
a local tru value or ace hardware store usually has the "rutland" display who manufactures all the products you will need for this issue.
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
Most gaskets are secured to the non-moving part...
Glue it to the stove not the moving lid...
You might want to dry fit some flat gasket also...
Rope might have too much bulk...
Glue it to the stove not the moving lid...
You might want to dry fit some flat gasket also...
Rope might have too much bulk...
- rockwood
- Member
- Posts: 1381
- Joined: Sun. Sep. 21, 2008 7:37 pm
- Location: Utah
- Hot Air Coal Stoker Furnace: Stokermatic
- Hand Fed Coal Stove: Rockwood Stoveworks Circulator
- Baseburners & Antiques: Malleable/Monarch Range
- Coal Size/Type: Lump and stoker + Blaschak-stove size
3/8 inch fiberglass gasket I think would work and it might be easier to remove the lid to get the hinge side in.
I agree with CapeCoaler, it should be glued to the stove not the lid.
I agree with CapeCoaler, it should be glued to the stove not the lid.
-
- New Member
- Posts: 5
- Joined: Sun. Oct. 18, 2009 1:50 am
yes glue the rope to the groove on the stove and crack open a cold one )
- wsherrick
- Member
- Posts: 3744
- Joined: Wed. Jun. 18, 2008 6:04 am
- Location: High In The Poconos
- Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
- Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
- Coal Size/Type: Chestnut, Stove Size
I have another question for you. I didn't see a pipe damper installed in your stove pipe. Your stove will certainly require one if you don't have one on there.
Really? I must have mistakenly assumed the damper on the stove itself would be enough. How far up the pipe should I put it?wsherrick wrote:I have another question for you. I didn't see a pipe damper installed in your stove pipe. Your stove will certainly require one if you don't have one on there.
- wsherrick
- Member
- Posts: 3744
- Joined: Wed. Jun. 18, 2008 6:04 am
- Location: High In The Poconos
- Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
- Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
- Coal Size/Type: Chestnut, Stove Size
You can place the pipe damper anywhere around 2 feet from the stove exhaust collar. Place it where it will be convenient to reach. Location is not critically important. You gotta have one though. You have a neat stove there. Once you learn how to use it, you won't trade it for a modern one. Let's see some photos of it when you get it all fired up.