Better Shaker Handle ??
- xaos
- Member
- Posts: 163
- Joined: Sat. Nov. 22, 2008 9:38 pm
- Location: Elizabeth TWP. Pa.
- Hot Air Coal Stoker Furnace: Alaska 140 Auger
- Hot Air Coal Stoker Stove: Alaska Stoker 1
- Coal Size/Type: Rice
OK. This is the 4th season with my USSC Ashley 24A and I have broken another shaker handle..;
They seem to be just cheaply made of some cast/pot metal..
is there a better handle that someone makes??
it has a 3/4 " square female end.
I have used several different sockets but the end stripping off the squared end of mt grate..
They seem to be just cheaply made of some cast/pot metal..
is there a better handle that someone makes??
it has a 3/4 " square female end.
I have used several different sockets but the end stripping off the squared end of mt grate..
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
If you do find a replacement, try lightening up on your shaking enthusiasm.
- LsFarm
- Member
- Posts: 7383
- Joined: Sun. Nov. 20, 2005 8:02 pm
- Location: Michigan
- Stoker Coal Boiler: Axeman Anderson 260
- Hand Fed Coal Boiler: Self-built 'Big Bertha' SS Boiler
- Baseburners & Antiques: Keystone 11, Art Garland
You are probably going to have to have a good, tight fitting handle made to fit the stub of the axle of the shaker grate. The antique stoves used a triangular shaped stub which provided more pronounced corners to transfer the torque of the handle to the grate. A square has smaller corners and will strip easier.
The key is to get a tight fit. could you braze a 1/2" or 3/4" square drive socket to the stub of the grate? then use a 'speed' handle in 1/2" or 3/4" drive to be your shaker handle?? the better quality steel in the socket and speed handle should make them last longer.
Just an idea,
Greg L
The key is to get a tight fit. could you braze a 1/2" or 3/4" square drive socket to the stub of the grate? then use a 'speed' handle in 1/2" or 3/4" drive to be your shaker handle?? the better quality steel in the socket and speed handle should make them last longer.
Just an idea,
Greg L
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Gottchaxaos wrote:I blame the coffee..
- xaos
- Member
- Posts: 163
- Joined: Sat. Nov. 22, 2008 9:38 pm
- Location: Elizabeth TWP. Pa.
- Hot Air Coal Stoker Furnace: Alaska 140 Auger
- Hot Air Coal Stoker Stove: Alaska Stoker 1
- Coal Size/Type: Rice
Brazing a socket on would interfere with the door closing. I was using a 7/8 16 point deep well end of last year through most of this year, and the stub started rounding off some tried several different sizes but just didn't hold right.LsFarm wrote:You are probably going to have to have a good, tight fitting handle made to fit the stub of the axle of the shaker grate. The antique stoves used a triangular shaped stub which provided more pronounced corners to transfer the torque of the handle to the grate. A square has smaller corners and will strip easier.
The key is to get a tight fit. could you braze a 1/2" or 3/4" square drive socket to the stub of the grate? then use a 'speed' handle in 1/2" or 3/4" drive to be your shaker handle?? the better quality steel in the socket and speed handle should make them last longer.
Just an idea,
Greg L
ordered a new handle just last week and it broke on me this morning..
I was just looking online at a 1" OD square tube with an ID of 3/4"..
might have to bust out the smoke wrench and welder for a handle fab...
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
That's the route I take when I can. At least that way, you'll know exactly what you've got.
- Freddy
- Member
- Posts: 7301
- Joined: Fri. Apr. 11, 2008 2:54 pm
- Location: Orrington, Maine
- Stoker Coal Boiler: Axeman Anderson 130 (pea)
- Coal Size/Type: Pea size, Superior, deep mined
Given exact dimensions I could weld one up out of steel fairly easily. I'm guessing for $20ish dollars one could be in your hands... you do the painting!
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
By God, there's a deal, plus it'll get Freddy up outa that chair.