Feed Rate MAX?

Should we be fine tuning the max feed rate to get 1" to 1-1/2" of ash at edge of grate for more efficient operation? Will it cause over shoots? Thanks.

Mines about a inch or so away set at 43max when burning on max FR for awhile. I just leave mine at 40 because my FR usually only goes to 50 or 60..

Depends on how much heat is needed to satisfy the thermostat, mine is at Max. 48 and still have a good 1-2" of ash and it cranks out the heat when needed. I don't think I need to tune it up any more. It has more in it if needed, mine is only running 50-70% of max of the stove and seems to keep up nicely. I would probably roast myself if cranked any higher.

my max feed rate is set at 24 if it gets real cold like in the single digets than i turn it up to 28 and it will keep up but when it gets to the 20's i turn back down to 24. when i got the coal trol i was having pretty good overshoots set at max. i talked to paul or neil do not remember which one but he said because my stove is set to heat a 2500 sgft house and mine is only 1600 i should turn down max. seemed to work for me. i love this thing. my min is at 4 anybody go lower than this? i have a direct vent alaska channig

My Channing III is set Min4, Max42.

BK

hey bk i have talked to you before you have a huge house correct. compared to mine. i have redone every room in house. i have 9 ft ceilings. don't know if i spelled that right. have you gone below 4 on min? i do not get over shoots when it is warm. sometimes when i do not turn up max my temp will be 2-3 degrees below what i have it set at until we get up and start to move air around. your thoughts?

Mine will slowly go out if I set my Min below 4, I am heating 1500Sq ft story and a half, 75 year old house with 9ft ceilings. I don't have any overshoot more than 1 degree ever. I use my fan on my furnace to move the air.

BK

I bumped mine from 48 to Max 50 last night to see what it would do, WOW, it raised the stove temp almost 50 degrees on the front, it was 450 this morning, A little overshoot by 1-2 degrees. It's cranking right along! Phew. Supposed to get warmer, the few days....

I fired up my new LL Pioneer a week ago and been running since. Temps outside were about 65-70* for highs and mid 50*s at night. Factory settings were 4 min and 40 max. Bumped min up to 5 (not much I know) to make sure fire did not die out or under draft. My FR was 19% when it was 70* out, while trying to keep basement at 80*. The last day or two outside temps have been dropping. This morning it was 32* when I got up. Basement was at 80*, but FR was up to 96%. Now my questions are: Should I raise min speed a few points so that if it gets warmer out and stove is still running I can be sure of maintaining draft? And should I, as it gets colder on average outside, raise the max setting as high as possible without sending unburned coal to the ash pan at 100% FR? Seems like yes is obvious answer but with factory settings where they were and other posters min/max numbers, I don't want to stray too far w/o advice.

check the coal trol testing thread under leisure lines board it sounds good

I ususally don't touch mine, except maybe 1-2 points on the max to get a little more out of the stove if it's really cold. I haven't changed the min. setting, I have run mine at 65 degrees outside without going out.

You shoudl have a manometer or draft gauge to check to make sure you have some draft when warm outside. When warm, mine is really low (.01-.02), but still pulls up the chimney.

coldwind,

You could probably turn that MIN up to 6 or so if you like. Anything more probably won't be necessary. If you're concerned about undrafting then I suggest getting a hold of a manometer and seeing what you're pulling while it is still warmish out, or roll with it for the fall and check it in the spring. You shouldn't have any issues in the winter. On the MAX, you are right, you want to get it adjusted as high as possible while maintaining a good inch to 1.5" or so of ash at the end of the grate.

check out the manomater loaner program here in the forum

What is the highest anyone has their max free rate set at on the coal-trol digital thermostat?? Just curious??

I had mine set at 97 when running the Harman Magnum.