Getting Ready to Install LL WL110

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Sun Aug 17, 2014 8:34 pm

Don, the only port in this boiler are the two shown in the picture. There is no other place to put the aquastat or the PRV that i see.
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: StokerDon On: Sun Aug 17, 2014 9:08 pm

I see what you mean. There are a few pictures of WL110 installs in Pictures Of Your Boiler
It's a "pictures of your boiler" thread. It looks like they insatll the aquastat in a port just below the temp gage. At least I think that's and aquastat.

-Don
StokerDon
 
Stoker Coal Boiler: Yellow Flame "Competion Series" 3 grate boiler, Losch 475
Hot Air Coal Stoker Stove: Alaska Stoker1? can't figure out these dern Alaska names!!! It's a big old black one.
Hand Fed Coal Furnace: Harman SF3500
Coal Size/Type: Rice and Chestnut
Other Heating: Noth'in but COAL! Well, Maybe a little tiny bit of wood

Re: Getting Ready to Install LL WL110

PostBy: Flyer5 On: Mon Aug 18, 2014 10:37 pm

The small aquastat is the high limit and dumpzone control and is mounted in the outgoing loop. The triple aquastat that controls the boiler / feeder is the one mounted in the front of the coil.
Flyer5
 
Stoker Coal Boiler: Leisure Line WL110
Hot Air Coal Stoker Stove: Leisure Line Pioneer

Visit Lehigh Anthracite

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Tue Aug 19, 2014 12:23 pm

Flyer5 wrote:The small aquastat is the high limit and dumpzone control and is mounted in the outgoing loop. The triple aquastat that controls the boiler / feeder is the one mounted in the front of the coil.


Thanks Flyer, so the set up in my picture is okay? Speaking of a dumpzone, I am in the process of figuring out how to address the need for one. I need to keep in simple as that the installation expenses are already way over budge. Any opinions how to economically address the need for a dumpzone?
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Tue Aug 19, 2014 1:13 pm

Z10396 wrote:
Flyer5 wrote:The small aquastat is the high limit and dumpzone control and is mounted in the outgoing loop. The triple aquastat that controls the boiler / feeder is the one mounted in the front of the coil.


Thanks Flyer, so the set up in my picture is okay? Speaking of a dumpzone, I am in the process of figuring out how to address the need for one. I need to keep in simple as that the installation expenses are already way over budge. Any opinions how to economically address the need for a dumpzone?


I actually have an idea on how to handle the dumpzone. My home has cathedral ceilings on one side and a landing with a second story on the other. The second story is comprised of the master bedroom which we never use the heat in because of the rising warm air from below. I am thinking that I should set this up as the dumpzone, that zone is never calling for heat anyways. Does this sound practical?
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: Sting On: Tue Aug 19, 2014 3:58 pm

You can do anything with enough ice cube relays and a little planning.

you can have every zone in the load circulate if you need it
Sting
 
Other Heating: BurnHAM=NG-gas

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Tue Aug 19, 2014 5:08 pm

With that said, would using that 3rd "unused zone in my 2nd story serve as an adequate dump zone? If so, how do I go about setting it up?
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: Boots On: Tue Aug 19, 2014 5:31 pm

Z10396 wrote:With that said, would using that 3rd "unused zone in my 2nd story serve as an adequate dump zone? If so, how do I go about setting it up?


As long as it's rated at enough btu's that it meets the manufacturers recommendation for the dump zone, yes.
Boots
 
Stoker Coal Boiler: Keystoker KA-6
Hand Fed Coal Boiler: Burnham SFB 101 (sold)

Re: Getting Ready to Install LL WL110

PostBy: Sting On: Tue Aug 19, 2014 5:57 pm

Z10396 wrote:With that said, would using that 3rd "unused zone in my 2nd story serve as an adequate dump zone? If so, how do I go about setting it up?


you want a signal from the boiler vessel that will start and stop the flow in an over temp Like I attempted to show boots here How can I make this work.

or something similar

It Depends!
Sting
 
Other Heating: BurnHAM=NG-gas

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Tue Aug 26, 2014 9:59 pm

Finally have it plumbed in, just a little bit of soldering left to do. Then on to the power venter and then the electrical. I know it's not the prettiest install but I am happy with it for a novice. Any advice on my next steps? Thanks
Attachments
image.jpg
(127.14 KiB) Viewed 46 times
View: New PagePopup • Select:BBCode
[nepathumb]52962[/nepathumb]
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: McGiever On: Wed Aug 27, 2014 7:15 am

Over budget is not a good thing...but saving hundreds and thousands of dollars every heating season will help fade that memory. ;)
McGiever
 
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hot Air Coal Stoker Stove: HARMAN MAGNUM
Hand Fed Coal Stove: RADIANT HOME AIR BLAST
Baseburners & Antiques: OUR GLENWOOD 111 BASEBURNER "1908"
Coal Size/Type: PEA / ANTHRACITE, NUT-STOVE / ANTHRACITE
Other Heating: Ground Source Heat Pump
Stove/Furnace Make: Hydro Heat /Mega Tek

Re: Getting Ready to Install LL WL110

PostBy: Rob R. On: Wed Aug 27, 2014 7:52 am

You need to turn the circulator 90 degrees. The motor shaft must be horizontal.
Rob R.
 
Stoker Coal Boiler: EFM DF520
Hand Fed Coal Stove: Hitzer 50-93
Other Heating: Dad's 1953 EFM Highboy

Re: Getting Ready to Install LL WL110

PostBy: Sting On: Thu Aug 28, 2014 8:55 am

They never listen - but they can complain when its -20 ---- winds out of the North --- and call me out of bed. :mad:
Sting
 
Other Heating: BurnHAM=NG-gas

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Thu Aug 28, 2014 5:03 pm

Rob R. wrote:You need to turn the circulator 90 degrees. The motor shaft must be horizontal.

Thank you, I turned it.
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Re: Getting Ready to Install LL WL110

PostBy: Z10396 On: Thu Aug 28, 2014 5:56 pm

Sting wrote:You can do anything with enough ice cube relays and a little planning.

you can have every zone in the load circulate if you need it

I think I am going to have it dump and circulate to all three zones. The plumbing is done, now on to the wiring.
Z10396
 
Stove/Furnace Make: Leisure Line
Stove/Furnace Model: WL110

Visit Lehigh Anthracite