Exhaust Temperature coming off the WL110

Exhaust Temperature coming off the WL110

PostBy: kstills On: Sat Nov 09, 2013 3:08 pm

Matt, Dave or anyone that's measured this, anyone know what the temps are coming off the top. Full bore burn, what's the max you would expect to see?
kstills
 
Stoker Coal Boiler: WL 110
Stove/Furnace Make: Leisure Line

Re: Exhaust Temperature coming off the WL110

PostBy: Matthaus On: Sat Nov 09, 2013 3:39 pm

Flue gas temp @ 200* F water temp would be between 300*F and 375*F depending on coal and how clean the boiler is and coal quality.
Matthaus
 
Stoker Coal Boiler: Leisure Line WL110 Dual Fuel, natural gas
Hot Air Coal Stoker Stove: Leisure Line Lil' Heater (rental house)
Coal Size/Type: Rice and Buckwheat Anthracite

Re: Exhaust Temperature coming off the WL110

PostBy: kstills On: Sat Nov 09, 2013 4:08 pm

So has anyone used aluminum tubing for venting?
kstills
 
Stoker Coal Boiler: WL 110
Stove/Furnace Make: Leisure Line

Visit Leisure Line Stove

Re: Exhaust Temperature coming off the WL110

PostBy: Rob R. On: Sat Nov 09, 2013 4:19 pm

Galvanized yes, aluminum no.
Rob R.
 
Stoker Coal Boiler: EFM DF520
Hand Fed Coal Stove: Hitzer 50-93
Other Heating: Dad's 1953 EFM Highboy

Re: Exhaust Temperature coming off the WL110

PostBy: kstills On: Sat Nov 09, 2013 4:49 pm

Rob R. wrote:Galvanized yes, aluminum no.


No you haven't tried it, or no it won't work?

Seems to have the chem resistance needed.
kstills
 
Stoker Coal Boiler: WL 110
Stove/Furnace Make: Leisure Line

Re: Exhaust Temperature coming off the WL110

PostBy: Rob R. On: Sat Nov 09, 2013 4:55 pm

No, I have not tried it. Aluminum vent pipe is only approved for gas installations...it doesn't have sufficient resistance to corrosion to be used with fuel oil appliances, so I doubt it would last very long with coal.
Rob R.
 
Stoker Coal Boiler: EFM DF520
Hand Fed Coal Stove: Hitzer 50-93
Other Heating: Dad's 1953 EFM Highboy

Re: Exhaust Temperature coming off the WL110

PostBy: Rigar On: Sat Nov 09, 2013 6:04 pm

...you just got "Robbed". :lol:
...aluminum and coal- bad idea
Rigar
 
Hot Air Coal Stoker Furnace: Keystoker A 150
Coal Size/Type: anthracite rice
Stove/Furnace Make: Keystoker
Stove/Furnace Model: A 150 warm air furnace

Re: Exhaust Temperature coming off the WL110

PostBy: kstills On: Sat Nov 09, 2013 6:27 pm

I found some flexible rubber compounds with high temp ratings up to 550f, but it's about elebenty thousand dollars to do 12 feet.

Anyone paint the galvanized to improve corrosion resistance?
kstills
 
Stoker Coal Boiler: WL 110
Stove/Furnace Make: Leisure Line

Re: Exhaust Temperature coming off the WL110

PostBy: 2001Sierra On: Sat Nov 09, 2013 7:12 pm

Galvanized is also a bad idea. It can gas off, which would not be healthy.
2001Sierra
 
Hot Air Coal Stoker Stove: Keystoker 90 Chimney vent
Coal Size/Type: Rice
Other Heating: Buderus Oil Boiler 3115-34
Stove/Furnace Model: Keystoker 90 Chimney Vent

Re: Exhaust Temperature coming off the WL110

PostBy: Rob R. On: Sat Nov 09, 2013 7:29 pm

2001Sierra wrote:Galvanized is also a bad idea. It can gas off, which would not be healthy.


Not anywhere near the stack temperature that a stoker boiler runs...which is under most oil units.
Rob R.
 
Stoker Coal Boiler: EFM DF520
Hand Fed Coal Stove: Hitzer 50-93
Other Heating: Dad's 1953 EFM Highboy

Re: Exhaust Temperature coming off the WL110

PostBy: Lightning On: Sun Nov 10, 2013 7:29 am

Matthaus wrote:Flue gas temp @ 200* F water temp would be between 300*F and 375*F depending on coal and how clean the boiler is and coal quality.


IS that water temperature? 300-375 degrees?? :?
Lightning
 
Hand Fed Coal Furnace: Clayton 1537G
Coal Size/Type: Nut/Stove Size Mix

Re: Exhaust Temperature coming off the WL110

PostBy: Rob R. On: Sun Nov 10, 2013 7:43 am

Lightning wrote:
Matthaus wrote:Flue gas temp @ 200* F water temp would be between 300*F and 375*F depending on coal and how clean the boiler is and coal quality.


IS that water temperature? 300-375 degrees?? :?


I read it as: With the boiler water temperature @ 200F, the internal stack temperature should be 300F to 375F.
Rob R.
 
Stoker Coal Boiler: EFM DF520
Hand Fed Coal Stove: Hitzer 50-93
Other Heating: Dad's 1953 EFM Highboy

Re: Exhaust Temperature coming off the WL110

PostBy: Lightning On: Sun Nov 10, 2013 7:48 am

Rob R. wrote:I read it as: With the boiler water temperature @ 200F, the internal stack temperature should be 300F to 375F.


Oh right lol, that's better.. I guess the way its worded I misinterpreted the data :lol:
Lightning
 
Hand Fed Coal Furnace: Clayton 1537G
Coal Size/Type: Nut/Stove Size Mix

Re: Exhaust Temperature coming off the WL110

PostBy: lsayre On: Sun Nov 10, 2013 7:49 am

Rob R. wrote:
Lightning wrote:
Matthaus wrote:Flue gas temp @ 200* F water temp would be between 300*F and 375*F depending on coal and how clean the boiler is and coal quality.


IS that water temperature? 300-375 degrees?? :?


I read it as: With the boiler water temperature @ 200F, the internal stack temperature should be 300F to 375F.


I had to do a double take on it. Not to nitpick, but if the "@" was to be replaced with the word "for" it would be easier to understand (properly).
lsayre
 
Stoker Coal Boiler: AHS S130 Coal Gun
Coal Size/Type: Anthracite Pea
Other Heating: Resistance Boiler (if I ever get it fixed)

Re: Exhaust Temperature coming off the WL110

PostBy: McGiever On: Sun Nov 10, 2013 10:24 am

For a New Topic...
How many members get their boiler water temps up to 375* F?
And if you have, did you have any leaks?
McGiever
 
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hot Air Coal Stoker Stove: HARMAN MAGNUM
Hand Fed Coal Stove: RADIANT HOME AIR BLAST
Baseburners & Antiques: OUR GLENWOOD 111 BASEBURNER "1908"
Coal Size/Type: PEA / ANTHRACITE, NUT-STOVE / ANTHRACITE
Other Heating: Ground Source Heat Pump
Stove/Furnace Make: Hydro Heat /Mega Tek

Visit Leisure Line Stove