Got Lucky!!!
-
- Member
- Posts: 128
- Joined: Thu. Sep. 15, 2011 8:12 pm
- Location: Erieville New York
- Hand Fed Coal Stove: Hitzer 50-93
- Coal Size/Type: nut/stove
I had to change the glass door gasket on my Hitzer. Was dreading it after all the stories Ive heard on here, So I finally got to it this week and boy did I luck out ! Sprayed the screws down with a ton of PBY Blaster end let it sit overnight. went down the next after noon and every single one of the screws came out ! Guess I should have played the lottery too !
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Amazing how things go when done the RIGHT way Chester---NICE
- Sunny Boy
- Member
- Posts: 25726
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Maybe it's also that central NY air. Clean country livin' !
Paul
Paul
-
- Member
- Posts: 4837
- Joined: Wed. Apr. 03, 2013 1:24 pm
- Location: Elkhart county, IN.
- Hand Fed Coal Stove: 1 comforter stove works all iron coal box stove, seventies.
- Baseburners & Antiques: 2014 DTS C17 Base Burner, GW #6, GW 113 formerly Sir Williams, maybe others at Pauliewog’s I’ve forgotten about
- Coal Size/Type: Nut Anth.
- Other Heating: none
Hey Fred,freetown fred wrote:Amazing how things go when done the RIGHT way Chester---NICE
great to see you're up and about enough to post.
thoughts and prayers,
steve
- Stoker6268
- Member
- Posts: 605
- Joined: Mon. Feb. 09, 2009 4:49 pm
- Location: Grafton NH
- Hand Fed Coal Stove: Hitzer 50-93
- Coal Size/Type: Pea
What stories? I had to replace mine due to a defect. No problems. Did it with the stove burning. Took less than 2 minutes. I assume people have trouble with the bolts? Mine was only a few months old so maybe thats why I didnt have problem...
- Pancho
- Member
- Posts: 906
- Joined: Sat. Feb. 01, 2014 4:00 pm
- Location: Michigan
- Baseburners & Antiques: Glenwood No. 8
- Coal Size/Type: Stove
- Other Heating: Jotul Firelight
On my old wood stove (used since 1999) they used socket head metric fasteners. No matter where the fastener was in the fire box, the screws always backed out easily. I think they were pretty hard as fasteners go and they also had a black oxide looking finish on them. There was never any rust on them either.Stoker6268 wrote:What stories? I had to replace mine due to a defect. No problems. Did it with the stove burning. Took less than 2 minutes. I assume people have trouble with the bolts? Mine was only a few months old so maybe thats why I didnt have problem...
....they should probably use those on exhaust manifolds....
- Sunny Boy
- Member
- Posts: 25726
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
They used to on some of the racing header kits. That what the Black Jack kit I put on my AMX had. Probably too expensive for just production line OEM exhaust manifolds ?Pancho wrote:On my old wood stove (used since 1999) they used socket head metric fasteners. No matter where the fastener was in the fire box, the screws always backed out easily. I think they were pretty hard as fasteners go and they also had a black oxide looking finish on them. There was never any rust on them either.Stoker6268 wrote:What stories? I had to replace mine due to a defect. No problems. Did it with the stove burning. Took less than 2 minutes. I assume people have trouble with the bolts? Mine was only a few months old so maybe thats why I didnt have problem...
....they should probably use those on exhaust manifolds....
Paul
- Pancho
- Member
- Posts: 906
- Joined: Sat. Feb. 01, 2014 4:00 pm
- Location: Michigan
- Baseburners & Antiques: Glenwood No. 8
- Coal Size/Type: Stove
- Other Heating: Jotul Firelight
I put hardened studs/nuts on my Cutty......but I imagine the OE's have a cost and longevity equation. There's a reason they don't do it.Sunny Boy wrote:Pancho wrote:
They used to on some of the racing header kits. That what the Black Jack kit I put on my AMX had. Probably too expensive for just production line OEM exhaust manifolds ?
Paul