Glenwood Hickory

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 6:09 pm

Ok, I bought it and it's installed and running right now on dry ash, seems to make good heat so far it has this in the back which I'm assuming is for a tee and a piece of pipe for a clean out??

SWPaDon · Post by **SWPaDon** » Sun. Feb. 08, 2015 6:26 pm

That's actually for the 'back pipe' .

Smokeyja · Post by **Smokeyja** » Sun. Feb. 08, 2015 6:35 pm

SWPaDon wrote:That's actually for the 'back pipe' .

Some definitely worth looking into getting !

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 6:37 pm

right but what dose it do "I know dumb question" it don't actually go into the ash pit

SWPaDon · Post by **SWPaDon** » Sun. Feb. 08, 2015 6:38 pm

Smokeyja wrote:
SWPaDon wrote:That's actually for the 'back pipe' .
Some definitely worth looking into getting !

Yes, he needs one for sure.

D.Japan, look here: Geneva Oak Andes Stove on the back of Randy's stove is a back pipe. His stove is different than yours, but it will give you a good idea.

SWPaDon · Post by **SWPaDon** » Sun. Feb. 08, 2015 6:39 pm

D.lapan wrote:right but what dose it do "I know dumb question" it don't actually go into the ash pit

Your smoke goes down one side then up the other enabling you to extract more heat from the flue pipe, I believe.

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 6:43 pm

if its not for base heater drafting what is it s actual purpose/?

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 6:43 pm

oh ok I got it now
its split inside

SWPaDon · Post by **SWPaDon** » Sun. Feb. 08, 2015 6:44 pm

D.lapan wrote:oh ok I got it now
its split inside

Yes, I do believe.

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 6:44 pm

who could I check with to try and find one?

SWPaDon · Post by **SWPaDon** » Sun. Feb. 08, 2015 6:47 pm

Wilson's Woodstoves, Stove Hospital, Barnstables,

Sunny Boy · Post by **Sunny Boy** » Sun. Feb. 08, 2015 7:55 pm

Yup, that's the support base for the back pipe,....... that I mentioned in my pm to you.

I guess you haven't checked your pm's yet ?

You'll need to measure the width and the length of that oval, or the circumference. Then give those measurement's to Wilson. He's recasting the parts you'll needed.

The back pipe will greatly increase the heat extracting ability of the stove, plus it will give you more control over the draft. In the long run, it will more than pay for itself in getting more heat from every pound of coal.

Paul

D.lapan · Post by **D.lapan** » Sun. Feb. 08, 2015 8:03 pm

Sunny Boy wrote:Yup, that's the support base for the back pipe,....... that I mentioned in my pm to you. I guess you haven't checked your pm's yet ?

You'll need to measure the width and the length of that oval, or the circumference. Then give those measurement's to Wilson. He's recasting the parts you'll needed.

The back pipe will greatly increase the heat extracting ability of the stove, plus it will give you more control over the draft. In the long run, it will more than pay for itself in getting more heat from every pound of coal.

Paul

I read it after I posted on here again, dose anyone have his contact info

Sunny Boy · Post by **Sunny Boy** » Sun. Feb. 08, 2015 8:05 pm

He goes by the screen name "wilsons wood stoves".

Wilson Mull, 508-763-8941

Paul

Photog200 · Post by **Photog200** » Sun. Feb. 08, 2015 8:07 pm

Yes, if you go back through my thread about my Andes, it has photos of the back pipe when I took it apart to do some repairs. It has an internal baffle where the exhaust comes down one side and then up the other and out the chimney. It really does make a big difference in the efficiency of the stove. I only hooked this stove up yesterday so it is hard to tell just how much coal it is going to be using. Having said that, I have reloaded it twice now and it has taken just one coal hod to re-fill it both times.

Randy

Glenwood Hickory

Attachments