Stove Tools

 
User avatar
joeq
Member
Posts: 5743
Joined: Sat. Feb. 11, 2012 11:53 am
Location: Northern CT
Hand Fed Coal Stove: G111, Southard Robertson

Post by joeq » Sun. Feb. 21, 2016 11:33 am

Attached is a transformation of my collection of stove tools since the Surdiac. In the lower photo, (my most current collection), one of the most important tool needed, is missing. I still need to acquire it. That would be the correct shaker handle for the draw center, and grate. But all the ones shown, serve a purpose, and aren't there for decoration. I may need to expand my wall holder. It's getting cramped.
stove tools 001.JPG
.JPG | 94.2KB | stove tools 001.JPG
xmas 2014 003.JPG
.JPG | 75.6KB | xmas 2014 003.JPG
stove tools 001.JPG
.JPG | 109.4KB | stove tools 001.JPG


 
User avatar
Sunny Boy
Member
Posts: 25697
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Sun. Feb. 21, 2016 1:36 pm

Joe,

The right shaker handle can make a difference. My range had the wrong one with it when I got it. Fit too lose and was abusing the triangular end of the grate bar. When I got an original Glenwood, it fit better and did a better job of clearing ash without beating up the grate bar end.

I see a lot of duplication in tools, that as time goes by you may find you can do without to simplify your storage rather than increase it. Unless you like collecting tools. Then yes, your gonna need a lot more hooks. :D

Paul

 
User avatar
joeq
Member
Posts: 5743
Joined: Sat. Feb. 11, 2012 11:53 am
Location: Northern CT
Hand Fed Coal Stove: G111, Southard Robertson

Post by joeq » Sun. Feb. 21, 2016 2:06 pm

Very observant Paul. I could do without a couple pokers, and the one shovel with the bent end, was used to scoop pea coal out of the Surdiac hopper, when I needed to M/T it for varying reasons. I should send it to Tim. And I also agree that using a sloppy tool in the D/C end isn't very efficient. As a matter of fact, the cast pin that sticks down through the slot in the DC is also sloppy, and I'm contemplating making some type of heat resistant bushing, to prevent the added impact while shaking.

 
User avatar
Lightning
Site Moderator
Posts: 14669
Joined: Wed. Nov. 16, 2011 9:51 am
Location: Olean, NY
Stoker Coal Boiler: Modified AA 130
Coal Size/Type: Pea Size - Anthracite

Post by Lightning » Sun. Feb. 21, 2016 4:11 pm

Stove tools?

Attachments

20160206_182650-1-1.jpg
.JPG | 871KB | 20160206_182650-1-1.jpg

 
User avatar
Sunny Boy
Member
Posts: 25697
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Sun. Feb. 21, 2016 4:25 pm

Lightning wrote:Stove tools?
Lee,
And that's not even counting the "stove tools" you have that need batteries !!! :D

Paul

 
User avatar
joeq
Member
Posts: 5743
Joined: Sat. Feb. 11, 2012 11:53 am
Location: Northern CT
Hand Fed Coal Stove: G111, Southard Robertson

Post by joeq » Sun. Feb. 21, 2016 4:26 pm

There you go Lee. Looks like you've got some doubles in there too. And Wow! You sure do have long tools. :D

 
lobsterman
Member
Posts: 727
Joined: Tue. Sep. 28, 2010 7:51 am
Location: Cape Cod
Hand Fed Coal Stove: Chubby, 1980 Fully restored by Larry Trainer
Hand Fed Coal Furnace: Chubby Jr, early model with removable grates

Post by lobsterman » Sun. Feb. 21, 2016 6:59 pm

joeq wrote:There you go Lee. Looks like you've got some doubles in there too. And Wow! You sure do have long tools. :D
and the big bad wolf said " All the better to poke you with, my dear."


 
User avatar
tcalo
Member
Posts: 2072
Joined: Tue. Dec. 13, 2011 4:57 pm
Location: Long Island, New York
Baseburners & Antiques: Crawford 40
Coal Size/Type: Nut/stove anthracite

Post by tcalo » Mon. Feb. 22, 2016 12:14 pm

This is all I need to get the job done...a shovel, a shaker handle and a poker!

Attachments

image.jpeg
.JPEG | 170.8KB | image.jpeg

 
User avatar
Sunny Boy
Member
Posts: 25697
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Mon. Feb. 22, 2016 12:54 pm

All I need for the range.

Shovel, poker, lid lifter, shaker handle.

Mechanics swiveling inspection mirror for checking where/what to use the poker on to free it upward if the grates get jammed.

And BBQ tongs for picking any good sized still burning embers out of the ash pan and put them back into the firebox, so as not to waste any if they drop through while shaking the grates.

Paul

Attachments

DSCN1681.JPG
.JPG | 135.9KB | DSCN1681.JPG

 
User avatar
joeq
Member
Posts: 5743
Joined: Sat. Feb. 11, 2012 11:53 am
Location: Northern CT
Hand Fed Coal Stove: G111, Southard Robertson

Post by joeq » Mon. Feb. 22, 2016 5:31 pm

Hey Paul, your above post reminds me of Steve Martin, in the movie "The Jerk". All I need is this bag, ...and this lamp! And nothing else. :lol: (you'ld have to see the movie to appreciate it.)
So none of you need a glove or two for hot ash pan removal? Or a wiss broom, for the "junk" that accumulates in the frt? Or a flashlight for seeing into the deep dark areas of the ashed up pot, or checking temperature readings in the dark? Maybe some differently shaped pokers? Or...this lamp? :D

 
User avatar
davidmcbeth3
Member
Posts: 8505
Joined: Sun. Jun. 14, 2009 2:31 pm
Coal Size/Type: nut/pea/anthra

Post by davidmcbeth3 » Mon. Feb. 22, 2016 11:38 pm

THERMOS !

 
User avatar
joeq
Member
Posts: 5743
Joined: Sat. Feb. 11, 2012 11:53 am
Location: Northern CT
Hand Fed Coal Stove: G111, Southard Robertson

Post by joeq » Mon. Feb. 22, 2016 11:53 pm

davidmcbeth3 wrote:THERMOS !
LOL. "And a rearend, thermometer too" :lol:

 
User avatar
Rob R.
Site Moderator
Posts: 18003
Joined: Fri. Dec. 28, 2007 4:26 pm
Location: Chazy, NY
Stoker Coal Boiler: EFM 520
Hand Fed Coal Stove: Chubby Jr

Post by Rob R. » Tue. Feb. 23, 2016 5:51 am

What happened to the simplicity of hand firing? Some of you have more tools than I have stoker parts!

 
User avatar
Sunny Boy
Member
Posts: 25697
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Tue. Feb. 23, 2016 8:16 am

joeq wrote:Hey Paul, your above post reminds me of Steve Martin, in the movie "The Jerk". All I need is this bag, ...and this lamp! And nothing else. :lol: (you'ld have to see the movie to appreciate it.)
So none of you need a glove or two for hot ash pan removal? Or a wiss broom, for the "junk" that accumulates in the frt? Or a flashlight for seeing into the deep dark areas of the ashed up pot, or checking temperature readings in the dark? Maybe some differently shaped pokers? Or...this lamp? :D
I don't count my ash pan gloves as tools. :D

But yes, got all those, too. But since they are used for other purposes and not stored near the stove, I don't count them as "stove tools". ;)

Paul

 
User avatar
Sunny Boy
Member
Posts: 25697
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Tue. Feb. 23, 2016 8:19 am

Rob R. wrote:What happened to the simplicity of hand firing? Some of you have more tools than I have stoker parts!
Rob,
Hand fired are so easy that some owners get bored and go looking for excuses to play with them. :D

Paul


Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”