They only open when you need more heat in the house. Sounds like things are working beautiful for you.corey wrote:To add the tstat has not opened since 11 this morning
Information and Operations of My Ashley Model BCAC
- SWPaDon
- Member
- Posts: 9857
- Joined: Sun. Nov. 24, 2013 12:05 pm
- Location: Southwest Pa.
- Hand Fed Coal Furnace: Clayton 1600M
- Coal Size/Type: Bituminous
- Other Heating: Oil furnace
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
She is doing great not added coal since 930 this morning blue ladies are dancing around stove top just glided at 360 for hours dropped a bit recently. I just think I could do better by making my draft more stable.
- Sunny Boy
- Member
- Posts: 25723
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Because those wind gusts are not having as much of an affect on the stove as you may think just by looking at the mano readings jumping up and down.corey wrote:To add the tstat has not opened since 11 this morning
That difference between .05 and .11 is so slight a change in pressure that without the use of a mano, which is a highly sensitive instrument, you couldn't feel the difference. That's .06 is not enough pressure to move the needle on an engine vacuum gauge.
If you were to keep checking the stove pipe with an IR gun, I doubt you'd see more surface temp variation than you would on a day that wasn't windy.
Watching the mano on a windy day and worrying about what affect it is having on a coal fire, is like looking at tiny bugs under a microscope and thinking they are big enough to bite your hand off.
Paul
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
corey wrote:She is doing great not added coal since 930 this morning blue ladies are dancing around stove top just glided at 360 for hours dropped a bit recently. I just think I could do better by making my draft more stable.
A barometric damper will help to decrease lag time of your bi-metal thermostat which first has to detect a change in stove temperature before acting. If draft changes radically it can't react fast, but first has to feel the result of that change. I believe Berlin recommended a baro for bit coal.
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
I'd like to better control heat output also.franco b wrote:corey wrote:She is doing great not added coal since 930 this morning blue ladies are dancing around stove top just glided at 360 for hours dropped a bit recently. I just think I could do better by making my draft more stable.
A barometric damper will help to decrease lag time of your bi-metal thermostat which first has to detect a change in stove temperature before acting. If draft changes radically it can't react fast, but first has to feel the result of that change. I believe Berlin recommended a baro for bit coal.
- SWPaDon
- Member
- Posts: 9857
- Joined: Sun. Nov. 24, 2013 12:05 pm
- Location: Southwest Pa.
- Hand Fed Coal Furnace: Clayton 1600M
- Coal Size/Type: Bituminous
- Other Heating: Oil furnace
Yes, he did. And as I said earlier, there is no problem in using one.franco b wrote: I believe Berlin recommended a baro for bit coal.
But before installing it, he better make DAMN sure all of the old creosote is gone. He already had one flue fire, the next one may take out his grandparents house with them in it.
My other point is.........most everyone is telling this poor fella that he has to have a 70 dollar device, when that 6 dollar one is working just fine.
It makes no sense at all.
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
I brushed my pipes almost to bare steel last week just a film if soot left. The mpd seems to hold heat in its don't need that. It's 40 degrees out and we have windows open cause it 81 in here few hours ago.
I need something to help me even things out instead of holding heat in.
I need something to help me even things out instead of holding heat in.
- Sunny Boy
- Member
- Posts: 25723
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Can you turn down the incoming air more without sooting it up ?corey wrote:I brushed my pipes almost to bare steel last week just a film if soot left. The mpd seems to hold heat in its don't need that. It's 40 degrees out and we have windows open cause it 81 in here few hours ago.
I need something to help me even things out instead of holding heat in.
Paul
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
It's been closed since this morning. But the stove has stayed in around 350 now it 280 so I don't think I have huge problem here. My draft just need tuned in its easy done but I have to play with the mpd.Sunny Boy wrote:Can you turn down the incoming air more without sooting it up ?corey wrote:I brushed my pipes almost to bare steel last week just a film if soot left. The mpd seems to hold heat in its don't need that. It's 40 degrees out and we have windows open cause it 81 in here few hours ago.
I need something to help me even things out instead of holding heat in.
Paul
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
Ah we good it's just mild and sunny day today. May I did to use some slack coal on these days.
Also the temperature readings are directly over the fire bed. I did load her up today I will say that.
Tomorrow and Monday is going to much colder and overcast skies with snow.
Also the temperature readings are directly over the fire bed. I did load her up today I will say that.
Tomorrow and Monday is going to much colder and overcast skies with snow.
- SWPaDon
- Member
- Posts: 9857
- Joined: Sun. Nov. 24, 2013 12:05 pm
- Location: Southwest Pa.
- Hand Fed Coal Furnace: Clayton 1600M
- Coal Size/Type: Bituminous
- Other Heating: Oil furnace
I think you should give things a while until you get accustomed to it. I also think you are just getting bored because the stove is running itself with very little input from you.corey wrote:Ah we good it's just mild and sunny day today. May I did to use some slack coal on these days.
Also the temperature readings are directly over the fire bed. I did load her up today I will say that.
Tomorrow and Monday is going to much colder and overcast skies with snow.
You can change if you want.........hell I really don't give a dam.
These guys in here brag all the time how they can spend other peoples money
-
- Member
- Posts: 1035
- Joined: Fri. Nov. 14, 2014 11:14 am
- Location: Southwest VA
- Hand Fed Coal Stove: Buck Stove Hybrid
- Coal Size/Type: Eastern KY bituminous
Bored??? Did not imply that I was I guess when it hit 40ish out side the fire will have to go out. All I am looking for is a way to better manage the heat.
No I was not saying that I don't like the stove Don.
No I was not saying that I don't like the stove Don.
- SWPaDon
- Member
- Posts: 9857
- Joined: Sun. Nov. 24, 2013 12:05 pm
- Location: Southwest Pa.
- Hand Fed Coal Furnace: Clayton 1600M
- Coal Size/Type: Bituminous
- Other Heating: Oil furnace
No one implied that either.corey wrote:Bored??? Did not imply that I was I guess when it hit 40ish out side the fire will have to go out. All I am looking for is a way to better manage the heat.
No I was not saying that I don't like the stove Don.
It just appears that you are 'looking to change' something with your setup.
It's 30 degrees outside up here. I'm only running half a firebox of coal in my furnace currently. Gotta adjust to the weather is all.